Robert,
You need to start over completely with the gribtonc build in the gribtonc
directory. ie,
% make clean
% make
If that doesn't do the trick, then maybe you can give me a login to look
at this first hand.
Robb...
On Wed, 14 Oct 1998, Robert J. Boucher wrote:
Robb,
You must be sick of hearing from me! I did as you said and added the
LDFLAGS line to the gribtonc directory Makefile. I then went back to
the src directory and ran the make command and I still got the same
error. The only thing I noticed different was that only got one Error
code underneath the FATAL 12. I also ran the make command in the
gribtonc directory and also got the same error there. Any more thoughts
I would be more than happy to try.
Thanks
Rob
Robb Kambic wrote:
>
> On Wed, 14 Oct 1998, Robert J. Boucher wrote:
>
> > > > > > Robb,
> > > > > >
> > > > > > Here is the info you requested regarding the fatal error I get when
I
> > > > > > run the make file when installing the gribtonc decoder.
> > > > > >
> > > > > > The type of box is an SGI O2, R10000 Processor 128MB Ram
> > > > > > The os is an IRIX 6.3
> > > > > > The version of the C compiler is MIPSpro C 7.2
> > > > > >
> >
> > > Robert,
> > >
> > > If this was the error from compiling gribtonc, then you need to add a line
> > > in the Makefile after line 15 for LDFLAGS:
> > >
> > > CFLAGS = -g
> > > LDFLAGS = -o32
> > >
> > > to tell the linker to use -o32.
> > >
> > > Hopefully this should solve your problem.
> > >
> > > Robb...
> > >
> >
> > Robb,
> >
> > I did as you said above and modified the netcdf Makefile with the above
> > two lines and it cleared up the netcdf compile error. So now the
> > udunits and the netcdf programs both compile without a problem but when
> > I finally went to compile gribtonc I still got an error. I have included
> > the output of the gribtonc Makefile with the error. I have also
> > attached the gribtonc Makefile. I was going to try to make the same
> > changes that you mentioned above to the gribtonc Makefile but there was
> > no CDFLAGS to put the LDFLAGS after. Thanks again for the help.
>
> Robert,
>
> This is the top level Makefile for all the decoders, you need to edit
> the Makefile in the gribtonc directory:
>
> % cd gribtonc
> % {edit} Makefile
>
> Make the above changes for CFLAGS and LDFLAGS and everything should
> compile correctly.
>
> Robb...
>
> >
> > Robert Boucher
> >
> >
> >
> >
> > ======
> Robb Kambic Unidata Program Center
> Software Engineer III Univ. Corp for Atmospheric Research
> rkambic@xxxxxxxxxxxxxxxx WWW: http://www.unidata.ucar.edu/
> ==============================================================================
--
Robert J. Boucher Tel: 971-942-2000 X2893
Associate MTS/Meteorologist Fax: 971-972-2571
Litton-TASC email: rjboucher@xxxxxxxx
55 Walkers Brook Drive
Reading, MA 01867-3297
==============================================================================
Robb Kambic Unidata Program Center
Software Engineer III Univ. Corp for Atmospheric Research
rkambic@xxxxxxxxxxxxxxxx WWW: http://www.unidata.ucar.edu/
==============================================================================